6 in 1 combo heat press machine factory China

This product is a multifunctional heat press machine heat transfer, can bake conventional cups, hot drilling, heat transfer, grilled cap, grilled 8-inch disk, 10-inch disk, printed T-shirts, pillows, mouse pads, puzzles, porcelain, etc. A metal plate machine for shop users!

· Electronic digital control, easy pressure adjustment, reliable performance
· Voltage: 220V
· Frequency: 50HZ
· Power: 1250W
· Heating plate size: 300mmx 380mm
· Machine size: 550mm x 500mm x 480mm
· 8-inch pan heating pad: Diameter 11cm
· 10 inch

                                                  Instructions                                                             

1. Check the stamping head if the reliable connection plug socket connector is connected with the electrical control box.

2. Plug in the power, turn on the power switch. (The machine rated voltage 220V, maximum input power 1250W)

: This equipment operating procedures set the device temperature display to Fahrenheit or Celsius

Starting temperature: Press the Mode button once to set, then set the indicator light according to plus or minus key to set the key starting temperature.

Maximum temperature: Press the Mode button to set the second, when the temperature indicator light, according to plus or minus key set to maximum temperature.

The most high-temperature baking time: Press the Mode button to set the third, then the time indicator light is on, press adder or subtracter key to set the key high-temperature baking time.

Pending state: Press the Mode button to set the fourth time, the machine will go into a pending state.

Note: The initial temperature setting range of 200 to 380 degrees, the highest temperature setting range of 200 to 430 degrees

The most high-temperature baking time setting range from 0 to 999 seconds.

The machine with a temperature setting self-locking function, namely as a starting temperature to 340 degrees, the machine will automatically

Limit the maximum temperature setting range from 340 to 430 degrees. Conversely, if the first set a maximum temperature of 250

Degree, the machine will automatically limit the initial temperature setting range from 200 to 250 degrees.

4. Stamping:

Slow-roasted: Object required stamping placed well, put pressure on reduction handle, turn the power switch, temperature open

Temperature beginning to rise. When the temperature has risen to starting point, the buzzer will sound, then press "ENTER",

End stamping... Remove objects, temperature

Degree will automatically return to the starting temperature gradually, at speed grilled standby.

Speed roast: at the starting temperature state, placed a good thing, pressing pressure handle, press Enter once,

End stamping... Remove objects, temperature

Degree will automatically return to the starting temperature gradually, again in quick roast standby.

* Lower than the initial temperature of the temperature, the temperature rises to the starting temperature ranges on the same press Enter to complete the whole stamping process, but after the temperature has risen in height, then the value is no longer good so pause in heating..

Bad design issue stamping tips:

Subdued colors: Temperature uneven or uneven pressure or time is too short.

Fuzzy pattern: long time cause the ink to spread.

Pattern Matte: excessive pressure or temperature is too high.

Local fuzzy pattern: Stamping regional heat unevenly distributed.

Scar pattern: transfer time is too long.

Pattern color shades: uneven pressure or uneven coating transfer objects.

Sticker: temperature is too high or bad thing transfer coating.

:( Stamping method recommended self trim specific practice in the future)

                                                                            Tile categories                                                                                       

Parameters: initial temperature was set to 230 degrees, the maximum temperature was set to 330 degrees,

Most high temperature baking time is set to 30 seconds.

Stamping:wipe surface with clean cloth, place transfer paper on bonded tile façade with a high temperature adhesive tape. Fix the tile face up, place in middle of silicone foam board handle stress reduction, such as reduction so the pressure won't be too big or small, adjust heat height.

metal plate:

Parameters: initial temperature was set to 230 degrees, the maximum temperature is set to 300 degrees,

Most high temperature baking time is set to 30 seconds.

Stamping: torn metal plate surface foil, transfer paper bonded metal panels on the front, with a high temperature adhesive tape

Fixed, right side up, put in the middle of the base silicone foam board, handle stress reduction, such as the pressure is too big or too small, adjustable head height, key operations, see page 4 for a detailed procedure.

Mug:

Parameters: initial temperature was set to 230 degrees, the maximum temperature was set to 330 degrees,

Most high temperature baking time is set to 30 seconds.

For continuous printing, printing can be completed in the first start after the temperature is adjusted 325 degrees, the highest temperature change

Most high temperature baking time was set to 120 seconds. Put the cup on the cup machine and press Enter.

Stamping: wipe surface with clean cloth, the transfer paper wrapped package mug with hot sticky tape

Place the cup in the hot machine mold cavity and put pressure on the handle, so as not to apply too much pressure use the adjustable pushrod stroke with key operations, see page 4 for a detailed procedure.

Fabric:

Parameters: initial temperature was set to 230 degrees, after the temperature has risen to 355 degrees,

The most high-temperature baking time :( pure chemical fiber or synthetic fabrics with sublimation paper containing 30 to 50 seconds, with a cotton T-shirt transfer paper 10 to 20 seconds)

Stamping:

Dish:

Parameters: initial temperature was set to 355 degrees, the maximum temperature is set for 355 degrees,

Most high temperature baking time is set to 30 seconds. After the temperature rose to the starting temperature and press Enter.

Immediately after pressing the handle the pressure starts.